Bay Windows Add Character And Space To A Home
It was the best area. Our California cattle ranch design home had a big picture window in the front room. The window extended from a few inches above the flooring to just a couple of inches below the cathedral ceiling. The walls and ceiling were redwood stained knotty pine and the floor was a coordinating hardwood. The window kept an eye out over a flower bed, shrubs and the expanse of front yard. It was the ideal window to be replaced with a bay window.
The window was nearly square. It was 72 X 72 inches. We considered a bow window, but elected to set up a bay window instead. We just felt that our specific home looked much better with 3 panel bay window rather than the numerous panel bow windows. Our intent was to fill the seat board of the bay with potted plants we had being in front of the existing photo window. The brand-new plan would provide us a little bit more area in the room and improve the total appearance of the house. It was time to go shopping.
Scratch vs. Pre-built
When we first understood of installing the new window, I began collecting plans for constructing a bay window. Thumbing through books and publications, and the Web online search engine, I discovered a number of prepare for building a bay window from scratch. I also found that carrying out such a project was going to be unneeded. The majority of the major window manufacturers, such as Pella, Milgard and Anderson make both entirely pre-assembled bay windows in addition to pre-built elements for bay windows.
These days extremely couple of professionals will handle the project of building a bay or bow window from scratch. It merely isn't practical when for the same or less cash they can install a high quality pre-built window. If the specialists utilize pre-built windows or elements for new house building and construction or remodelling tasks, then we might do the same for our redesigning task, we reasoned.
Installing a bay window can easily be a do-it-yourselfer project. Before you go the diy route, nevertheless, you may wish to line up a professional to help out if necessary. This is not going to be a task that you can complete during a Saturday afternoon. Opportunities are you are not going to finish it home owwnership tips in a weekend, for that matter.
You are also going to wish to line up some help. Bay windows and window components are heavy. A minimum of they are too heavy for someone to manage.
Be sure and have a look at the weather forecast, consisting of the long range projection. Setting up the window means opening a hole into your home. It can take a couple of days to get the new window in location and sealed. The last thing you want is for rain to come pouring in on your flooring, walls or furnishings.
Be sure and check your city or community building codes. There might be unique regional requirements, such as having shatterproof glass in low profile windows. You are probably going to require a building permit anyhow, so that is also a great time to check the codes.
Tools and Products Needed
The tools you will require for this job include a tape measure, a framing square that you can likewise utilize as a straight edge, a circular saw or miter saw, crow bars, drill and bits, level, stapler, energy knife, tin snips and a caulking weapon.
The products you will require include the bay window system, the assistance brackets, nails, roofing paper, shingles, roof nails, exterior grade silicone caulking and fiberglass insulation. You will also need 1X6 inch boards for the window skirting. If you are expanding an existing window, or if you are installing the window in an area that was previously the wall, you will likewise require 2X4s for cripple studs and extra framing.
Basic Setup Steps
1. Develop window position in the wall. Remove the existing window. Determining the bay window, mark on the exterior of the house the opening needed for the brand-new window. Utilizing your circular saw, cut the needed opening.
2. Framing. Build the framing for the new window. This will likely include cutting through existing studs and putting in a brand-new header, rough sill, jack studs and cripple studs.
3. Set up the support braces. A window approximately 5 feet large will take a minimum of two support braces. A larger window will need 3.
4. Set the window in location. Lift the bay window on the support braces and slide it into the rough opening. Shim as needed to level the window. Anchor in place.
5. Develop the window roofing. Set the roofing frame on top of the bay window unit and nail in place. Fill the space between the roofing and the top of the bay window with insulation. Fasten the roofing system sheeting to the Additional resources frame and cover with roofing paper. Set up the drip edges and the flashing and after that shingle.
6. Set up the window skirting around the bottom of the window. Fill will insulation and after that attach the skirt bottom to seal the underneath side of the window.
7. Seal the edges with silicone caulking.
This is a list of the fundamental setup actions and they have actually been abbreviated in the interests of simpleness and area. The window unit you buy will have complete setup actions. Take it from the voice of experience; it actually makes the task go much more efficiently and it will be completed in much less time when you read and follow them.
In our case, I had 2 pals assisting with the job. We have collaborated on other projects and work together well. We had the old window out and the rough framing finished on Saturday afternoon. We buttoned up the hole with plywood over night and went back to work the next day. By Sunday evening we had the brand-new window installed and the roofing system and skirting finished. On Monday afternoon I completed sealing up the outdoors and finished the trim work for the inside.
When it came time to offer your home, it was among the features that were particularly attractive to the buyers.